Omnimount Projector Accessories PMD1 User Manual

Installation Instructions  
PMD.5 — PMD1— PMD2:  
Universal Projector Mounts  
Thank you for purchasing an OmniMount product.  
Specifications are subject to change without prior notice.  
Every effort has been made to provide accurate and error-free assembly and installation.  
OmniMount Systems disclaims liability for any difficulties arising from the interpretation  
of information contained in these instructions. If OmniMount products are used for pur-  
poses other than their original intent, OmniMount, its distributors and retailers shall not  
be held responsible or liable for injuries or property damage, direct, indirect, or conse-  
quential, which may arise from the inability to use this product safely, properly, and in the  
manner for which it has been designed and manufactured. Warranty does not apply to  
products which have been lost, damaged by misuse, abuse, or accident.  
Universal Mounting Grid  
Superior Mounting Flexibility  
Adjustable Ceiling Pipe Drop  
OmniMount Systems, Inc.  
8201 South 48th Street • Phoenix, AZ 85044-5355  
IMPORTANT: To utilize the PMD projector mount, the projector must have  
mounting lands (threaded inserts) on the base. Contact OmniMount if you have any  
questions regarding the proper installation of this projector mount system.  
Questions? 1-800-MOUNT IT  
P/N 1002082—Rev. D 9/2004  
8
 
Part  
Projector Mounting Hardware  
Qty.  
Bag  
Step 5  
Fig. 6  
1
Large Washer  
8
4
(a)  
(a)  
Determine required mounting screw size (4, 5 or 6 mm)  
for projector. Note: Consult projectors owners’ manual  
for screw sizes and mounting holes.  
2
Metal Spacer: 3/8”  
3
Plastic Spacer: 1”  
1
(b)  
Hardware Bags  
PMD–.5 /PMD–1  
PMD-2  
Screw:  
6mm x 25mm  
Lay projector on table with mounting surface face up.  
Place grid section of bottom projector mounting plate  
onto top of projector in desired mounting orientation  
(horizontal or vertical). (Fig. 6)  
4
5
6
Screw:  
5mm x 25mm  
4
4
4
(c)  
(c)  
(c)  
Screw:  
4mm x 25mm  
Screw:  
5mm x 25mm  
Screw:  
Screw:  
3mm x 25mm  
4mm x 25mm  
Using a pencil or felt tipped pen, mark the locations of  
the projectors threaded inserts onto the grid for refer-  
ence. (Fig. 7)  
Step 1  
Verify that the dimensions (H x W) of the mounting lands on y0ur projector fall within  
the mounting grid footprint for your PMD mount.  
Fig. 7  
PMD .5  
Place a large washer (1) over mounting screw, and  
then insert screw through grid at marked location.  
(Fig. 8)  
PMD 1  
Fig. 8  
Lift the projector mounting plate and place a second  
large washer (1) onto the end of the screw, followed by a  
metal spacer (2). Loosely thread (2-3 turns) screw as-  
sembly into the chosen threaded insert on the bottom of  
the projector. (Fig. 9)  
PMD 2  
Fig. 9  
Repeat this procedure for the remaining threaded inserts.  
(Fig. 10)  
Note: A 1” plastic spacer (3) is included for projectors  
with uneven mounting surfaces. Trim the plastic spacer to  
the required length, and install on appropriate mounting  
screw.  
Fig. 10  
Once all mounting screws have been installed, square up the projector mounting plate,  
and then tighten the mounting screws securely.  
Caution: Do not force or over tighten the mounting screws, or damage to the projector  
may occur.  
6
3
 
Step 4  
Step 2  
Fig. 1  
With an electronic stud finder, locate center of ceiling stud in desired mounting loca-  
tion. Unscrew ceiling plate (E) from Projector Mounting top plate (A). Use ceiling plate  
as a template, and mark mounting hole locations. Drill mounting holes to a depth of 3”  
using a 3/16” drill bit. Mount ceiling plate to stud with 5/16” lag bolts (J).  
Gently pull the extension tube of the pipe drop as-  
sembly down to the required projector height. Rotate  
extension tube so that adjustment screw holes are  
visible through the support tube. (Fig. 1)  
Step 3  
Secure the pipe position by installing ½” long hex  
screws (I) into adjustment screw holes. For a cleaner  
appearance, insert plastic plugs (K) into unused  
holes on extension tube.  
Determine type of installation:  
Standard Ceiling Mount  
Extended Ceiling Mount  
Flush Mount  
Wall Mount  
Separate top and bottom projector mounting plates  
(A&B), by sliding them apart. (Fig. 2)  
Standard Ceiling Mount  
Press plastic cover (D) into place over ceiling plate.  
Attach pipe drop assembly (C) to ceiling plate with three 5/8” hex  
screws (H).  
Fig. 2  
Note: Orient the cable management port on the pipe drop assem-  
bly so that it faces the projector cable drop.  
Thread ¼” hex head set screw (F) into side of pipe collar,  
on top projector mounting plate (A). (Fig. 3)  
Extended Ceiling Mount  
Note: If necessary, screw in tilt knob to gain access to the  
set screw hole.  
For installations that require a ceiling drop in  
excess of 18”, standard 1 ½” pipe may be used  
to extend the standard pipe drop assembly.  
Fig. 3  
Pipe extension should be cut to the required  
additional length, threaded on both ends, and  
then attached to the standard pipe drop as-  
sembly with a pipe coupler (not supplied).  
Loosely thread top projector mounting plate (A) onto threaded  
portion of pipe drop.  
Note: Orient the cable management port on  
the pipe drop assembly so that it faces the  
projector cable drop.  
Position top projector mounting plate into desired orientation  
(horizontal or vertical), and then tighten set screw (F). (Fig. 4)  
Fig. 4  
Flush Ceiling Mount  
For installations with low ceilings, the flush ceiling mount  
should be used. Note: cable management is not available  
with the flush mount. Proceed to step 3.  
Thread cable bundle through cable management port at top of  
pipe assembly, down through the pipe assembly, and then out  
through the cable management port on the rear of the projector  
mounting plate. (Fig. 5) (Standard ceiling mount only) Be sure  
to leave enough cable to reach the mounted projector.  
Wall Mount  
Fig. 5  
With the addition of the OmniMount PMD-WM wall mount  
(sold separately); the PMD can be mounted to a wall instead  
of the ceiling. This is particularly useful for small confer-  
ence/classrooms where a ceiling mount is impractical. Refer  
to the PMD-WM installation instructions.  
Flush Ceiling Mount  
For flush ceiling mount, loosely thread top projector  
mounting plate directly onto threaded portion of ceiling  
plate. Note: Plastic cover is not used for flush mount.  
4
5
 

Multiquip Music Mixer WM63H5 User Manual
Murphy Switch WDU 0277 User Manual
Nikon Camcorder S2H05000501 User Manual
NordicTrack Treadmill NTL129054 User Manual
Nostalgia Electrics Mixer DMB 790 User Manual
Omega Vehicle Security Air Conditioner DRN ACC User Manual
Onkyo Stereo Receiver HT R494 User Manual
Panasonic Air Conditioner CS MKE12NKU User Manual
Panasonic Camera Accessories BTLH910GJ User Manual
Panasonic Network Card 2SC6036 User Manual